PermaClean 100 SL

Product Overview

Perma-Clean 100 SL is an NSF 600 potable water tank lining featuring single-leg applied 100% solids ceramic epoxy technology. This aliphatic amine epoxy may be used as a liner for steel or concrete water tanks and may also be specified for immersion service in treatment plant services such as clarifiers or aeration basins. Certified to NSF 61/600 standards and compliant with AWWA D102 ICS-3 specifications.

NSF 61/600 Certified

Approved for potable water contact in tanks 10,000 gallons and greater

100% Solids

Zero VOC, environmentally responsible formulation

Single-Leg Application

Efficient application process with advanced spray technology

AWWA D102 Compliant

Meets ICS-3 specifications for interior coating systems

Typical Uses

• Potable water storage tanks (steel and concrete)
• Clarifiers and aeration basins
• Water treatment plant immersion service
• Municipal water infrastructure
• Tanks requiring NSF 61/600 certification

Application Specifications

1604 ft² Coverage per gallon at 1.0 mil

45 ft² Coverage per gallon at 35 mils

15-50 mils Dry film thickness range

100% Volume solids

20 g/L VOC content

0 g/L HAPs

Application Methods

Single Leg Airless Spray: Remove all filters from spray system, use pump capable of 2,000 psi line pressure; 0.027-0.031 spray tip. Spray material at 90-105°F as measured at the gun. Graco Viscon in-line heater recommended. Insulated or heated hoses recommended for hose runs over 100 ft and cool ambient temperatures.

Perma-Clean 100 Cartridge Repair Kit: Tape off area to be repaired, pump cartridge five times into a waste cup to initiate mixing prior to applying material to substrate. See cartridge repair kit data sheet.

Brush and Roll: Recommended for small areas only.

Mix Ratio & Pot Life

Mix Ratio: 1:1 by volume A:B, pre-mix components prior to combining

Pot Life:

• 50°F: 3 hours
• 75°F: 1.5 hours
• 90°F: 45 minutes

Thinning

Do not thin. Use K-1070 or K-1034 for cleanup only.

Application Temperature: All steel temperatures must be ≥5°F above the dewpoint. Substrate temperature range: 40°F - 140°F. Material temperature range: 40°F - 120°F. Humidity range: 0% - 95% RH.

Surface Preparation

All substrates must be clean and dry, free of dirt, oils, greases and contaminants.

Carbon Steel

Abrasive blast to SSPC SP-10 with a 1-3 mil profile.

Concrete

Abrasive blast as per SSPC SP-13 to an ICRI CSP 3 or greater. Can be applied over Mortarchem and EFS 707.

Repairs, Small Areas

SSPC SP-11 power tool to bare metal to produce an angular profile.

Need Technical Support?

📞 800-324-9584

🎨 White, All Colors Available

Key Benefits

✓ NSF 61/600 Certified for Potable Water
✓ AWWA D102 ICS-3 Compliant
✓ 100% Volume & Weight Solids
✓ Zero HAPs
✓ Single-Leg Application System
✓ Excellent Chemical Resistance
✓ Direct to Metal or Concrete
✓ Immersion Service Capable

Compatible Primers

• Ceramaprime
• Ceramaprime LV
• Ceramaprime CC
• Indurazinc MC-67
• PE-70
• RC-70
• Direct to metal
• Direct to concrete

Cure Schedule

Dry to Topcoat (Min)

@ 50°F: 24 hours
@ 70°F: 12 hours
@ 90°F: 8 hours

Dry to Topcoat (Max)

@ 50°F: 30 days
@ 70°F: 30 days
@ 90°F: 7 days

Cured for Water Immersion

@ 50°F: 7 days
@ 70°F: 3 days
@ 90°F: 2 days

NSF 61/600 Certification

This product is certified for 10,000 gallons and greater tanks, not exceeding the maximum surface area per volume ratio of 36.8 sq.cm/L

Shelf Life & Storage

Shelf Life: 2 years (parts A and B)
Storage: Store long term between 35°F and 90°F
Pre-Application: Recommend heating material to 50-70°F in the 24 hours prior to application for ease of use

Induron