Product Overview
Perma-Clean 100 is an NSF 61/600 potable water tank lining. This 100% solids aliphatic amine ceramic epoxy may be used as a liner for steel or concrete water tanks and may also be specified for immersion service in treatment plant services such as clarifiers or aeration basins.
NSF 61/600 Certified
Approved for potable water tank lining applications
100% Solids Formula
Zero VOC (13 g/L), environmentally friendly
Extended Water Immersion
3 years no effect in water immersion at 120°F
Exceptional Salt Fog Resistance
10,000 hours ASTM B117 salt fog with no effect
AWWA D102 Compliance
Perma-Clean 100 meets AWWA D102 ICS-5 specification for interior coating systems.
Application Specifications
Application Methods
Airless Spray: Remove all filters from spray system, use Graco XP-70 or equivalent heated spray unit with heated hose bundle and in-line static mixer. 0.027-0.031 spray tip. Heat A and B components to between 90 and 110°F and spray at minimum line pressure to achieve fan
Cartridge Repair Kit: Tape off area to be repaired, pump cartridge five times into a waste cup to initiate mixing prior to applying material to substrate. See cartridge repair kit data sheet.
Brush and Roll: Recommended for small areas only
Pot Life
| 50°F | 75°F | 90°F |
|---|---|---|
| 30 minutes | 15 minutes | 5 minutes |
Cure Schedule
| Cure Stage | 50°F | 75°F | 90°F |
|---|---|---|---|
| Dry to Handle | 6 hrs | 3 hrs | 1 hr |
| Dry to Topcoat | 12 hrs | 8 hrs | 5 hrs |
| Cured for Water Immersion | 7 days | 24 hrs | 24 hrs |
Surface Preparation
All substrates must be clean and dry, free of dirt, oils, greases and contaminants.
Carbon Steel
Abrasive blast to SSPC SP-10 with a 1-3 mil profile
Concrete
Abrasive blast as per SSPC SP-13 to an ICRI CSP 3 or greater. Can be applied over Mortarchem and EFS 707
Repairs, Small Areas
SSPC SP-11 power tool to bare metal to produce an angular profile
Performance Testing
- ✓ ASTM D2794 Direct Impact: 80 in·lbs
- ✓ ASTM D4541 Adhesion to Ceramaprime primer: 1900 psi at 30 day primer cure
- ✓ NACE TM0174 Water Immersion at 120°F: 3 years no effect
- ✓ NACE TM0174 Water Immersion at 75°F: 3 years no effect
- ✓ NACE TM0174 Water Immersion in 1% sodium hypochlorite: 1 year, only color loss
- ✓ ASTM B117 Salt Fog: 10,000 hrs no effect
NSF 61/600 Certified
Potable Water Approved
Max ratio: 4.6 cm²/L
100% Solids
13 g/L VOC
Need Technical Support?
Available Kit Sizes
Note: All colors share a common Part A
Compatible Primers
- ● Ceramaprime
- ● Ceramaprime LV
- ● Ceramaprime CC
- ● Indurazinc MC-67
- ● PE-70
- ● Direct to metal
Application Conditions
- ● Substrate: 50-140°F
- ● Material: 90-120°F
- ● Humidity: 0-95% RH
- ● Steel ≥5°F above dewpoint
- ● Ambient ≥50°F
Storage
Store between 35 and 90°F. Recommend heating material to 80-85°F in the 24 hours prior to application.
Thinning
Do not thin. Use K-1070 or K-1034 for cleanup only.
Type: Surfacer Uses: Carbon Steel, Concrete Finish: Matte
Type: Surfacer Finish: Matte
