FAQ

[accordion]
[accordion-item title="Q: Do Induron coatings need a primer?"]
A: Induraguard 9200 is self-priming in most cases. For weathered galvanized R-1 to R-3, one coat is often enough at 8-10 mils to achieve a full 20-25 years of protection. For more corroded structures, Induron specifies a penetrating sealer, Ebond at 1.0-1.5 mils or Armorlux Alkyd Primer at 2.5-4 mils DFT.[/accordion-item]
[accordion-item title="Q: What is the lowest temperature in which the products can be applied?"]
A: Induron Ebond requires 50 degrees Fahrenheit to cure properly, but other primers can be applied in colder weather, such as MCU62 or Armorlux Primer. MCU63 will cure down to 32 degrees Fahrenheit, and Armorlux Primer is often applied in temperatures above 40 degrees Fahrenheit. In New England, coatings are generally applied from April to late November, so we have solutions for most weather conditions.[/accordion-item]
[accordion-item title="Q: Is there a preferred product for transmission and distribution towers?"]
A: For transmission and substation structures, the most specified system is either one coat of Indurguard 9200, a spot/full sealer, like Ebond, or a spot/full coat of primer, like Armorlux Primer. Many other coatings have been successfully applied depending on the specific situation. We have used many generic types of coatings, including water- borne acrylics and silicone alkyds.[/accordion-item]
[accordion-item title="Q. What is the typical length of time it takes for the product to be dry?"]
A: Depending on the temperature and humidity levels, many of the primers and sealers we use dry in a few hours. For instance, our Armorlux Light Grey primer dries like any medium-long oil alkyd primer and is normally ready to recoat the next morning. MCU62 cures rapidly at high humidity levels and at higher temperatures, which allows for
same-day recoating in many cases. The Ebond cures to recoat overnight above 50 degrees Fahrenheit, but may take slightly longer at temperatures around 50 degrees Fahrenheit.[/accordion-item]
[accordion-item title="Q. Can the products be used in high-humidity areas without any special preparation?"]
A: Most of Induron’s products have clear application guides that allow for wide ranges of humidity and temperature. We often switch sealers and primers in fall and spring, depending on the environment.[/accordion-item]
[accordion-item title="Q. What type of preparation is required before application?"]
A: Most T&D work involves wire brushes and paint scrapers. The logistics and cost of more advanced surface preparation is offset by the surface tolerance of the coating systems.
[/accordion-item]
[accordion-item title="Q. Is the product a low-VOC product?"]
A: The sealers, primers and 9200 vary in VOC, but we have a solution for every VOC requirement. Induraguard 9200 is very environmentally friendly and low in VOCs making it acceptable in every VOC district in the USA.[/accordion-item]
[accordion-item title="Q. Do your products address multiple applications?
"]

A: While there is no one-size-fits-all product, many of Induron’s products address different applications. Refer to our Technical Data Sheets for guidance on the proper applications for the product selection or call Induron Technical support at (800) 324-
9584 for more information.[/accordion-item]
[accordion-item title="Q. Are Induron products made in the USA?"]A: Yes! All Induron Coatings are made in Birmingham, Alabama.[/accordion-item]
[accordion-item title="Q. What do you need to apply the products? (Airless, brushes, rags, rollers, etc.)"]
A: T&D coatings can be applied by just about any method, including paint mitt, pound brush and roller. Usually, painters use mitts, rollers and brushes when applying paint to towers and poles and spray, brushes and rollers when applying paint to substation equipment.[/accordion-item]
[accordion-item title="Q. What is the coverage of one (1) gallon at one (1) mil thick?"]
A: Each product has a different coverage rate, which depends on the solids by volume and the recommended thickness range.[/accordion-item]
[accordion-item title="Q. Is Induraguard 9200 an epoxy?"]
A: No. Induraguard 9200 is a modified linseed oil alkyd fortified with three different types of barrier pigments.[/accordion-item]
[/accordion]